Beyond Tonnage: Sizing Press Brake Open Height, Stroke, and Throat Depth

Tonnage and bending length are where every press brake selection starts, and where most of them stop. Both confirm the machine can generate enough force across the required width. Neither tells you whether the part, once partly formed, can still move through the punch and die. A machine can bend the first three sides of a box cleanly and jam on the fourth, or complete every bend and leave the finished part wedged between the tooling with no way to pull it free.

Open height, ram stroke and throat depth catch this before it becomes a shop-floor problem. They confirm the part, tooling and bend sequence can physically pass through the machine without hitting the punch, the die holder or the frame.

Press brake dimension diagram showing bending length, distance between uprights, throat depth, ram stroke, and open height
Key press brake dimensions shown in the diagram: A, bending length; B, distance between uprights; C, throat depth from the tooling centerline to the rear of the C-frame; D, ram stroke; and E, open height (daylight).

The Deep U-Channel Problem

A deep U-channel with a return flange makes the point clearly. By the time the last bend is programmed, both side walls are already standing up from the previous operations. A machine with plenty of tonnage and a bed long enough for the part can still fail this bend if the punch, die holder or C-frame has nowhere to put those walls — the part either can’t be closed or can’t be removed afterward.

SpecificationDirectionWhat it determinesTypical failure mode
Open heightVerticalRoom for tooling, formed part, loading and removalTooling or part can’t fit between ram and bed
Ram strokeVerticalHow far the ram can travel to reach the bend positionPunch can’t reach the required depth
Throat depthHorizontal, toward the rear frameHow far a panel or flange can extend behind the bend linePart hits the C-frame

Open Height: The Maximum Vertical Space

Open height, also called daylight, is the vertical distance between the upper beam and the bed when the ram is fully open. The number on a spec sheet is a bare-machine measurement. Once punch holders, hydraulic clamps, adapters, punches, dies and die holders are installed, the usable space is smaller — often considerably smaller than the published figure suggests.

Before comparing two machines on this spec, confirm:

  1. The exact reference points the manufacturer measured from
  2. Whether the published figure includes any reference tooling or is bare-machine only
  3. The height of the upper clamping system and any adapters in your setup
  4. The lower die holder or table configuration
  5. The actual punch and die heights planned for the job

A part that slides into the machine flat, with no trouble at all, can still get stuck once it’s formed. Whether that happens comes down to how much of the published open height is actually left over after the real tooling stack is installed, not the bare-machine number on the spec sheet.

Ram Stroke: How Far the Ram Can Travel

Closed height is the same vertical measurement taken with the ram at its lowest position. The difference between open height and closed height is the ram stroke — the total distance the ram can travel.

Open height and stroke answer different questions. Open height determines whether the tooling and formed part fit in the machine. Stroke determines whether the ram can travel from that open position down to the depth the bend actually requires. The two don’t scale together automatically: a machine can have generous open height and comparatively limited stroke, or the reverse, depending on the frame and drive design.

This matters most in air bending, where the punch penetrates into the V-die until the material reaches the programmed angle. Required penetration depends on material thickness, tensile strength, die opening and target angle. If the installed tooling stack plus that penetration depth exceeds the available stroke, the ram can’t reach the bend position, regardless of how much open height sits above it.

Throat Depth: Rear-Frame Clearance

Throat depth is the horizontal distance from the tooling centerline back to the inside of the C-frame. It sets the limit on how far a sheet, panel or already-formed flange can extend behind the bend line before it contacts the frame.

Four-sided boxes and return flanges introduce a separate tooling-clearance check. For a four-sided box, the punch must be tall enough to clear the box during the final bend. For a return flange, the recessed profile of a gooseneck punch must provide enough space for the formed flange to pass without contacting the punch body. These tooling limits should be reviewed separately from machine throat depth, which describes the clearance behind the tooling centerline to the C-frame.

Throat depth and the distance between the machine’s uprights (also called column distance or distance between housings) are frequently mixed up, but they limit different things:

TermWhat it limitsWhen it becomes the binding constraint
Throat depthHow far a flange or panel extends behind the bend lineDeep boxes, wide panels, large return flanges
Distance between uprightsThe usable length of a part that must fit between the machine side framesLong workpieces, especially when formed geometry prevents the part from extending beyond or around the side frames
Backgauge travelHow far a blank can be positioned from the bend lineSetting up the bend location, not a physical clearance limit

Throat depth concerns how far a part can extend toward the rear of the machine. Distance between uprights concerns whether the workpiece and its formed geometry can fit between the side frames. Check both dimensions when a large or deep part must be rotated during the bend sequence.

CNHAWE press brake tooling chart showing multiple sheet metal bend profiles, straight and gooseneck punches, V-dies, and lower die mounting assemblies
Press brake tooling and bend profiles that shape the clearance requirements of deep channels, return flanges, hems, offsets, and other multi-stage bends.

Parts That Create Clearance Problems

Deep boxes and U-channels. The first two or three sides of a box bend without much drama. The fourth side is where problems show up, because by then two formed walls are already standing above the blank and a straight punch has no relief for them. A gooseneck punch’s necked profile lets the previously formed sides pass around the punch body instead of into it, but its relief depth becomes the new limiting number: exceed it, and the box can’t be closed no matter how much open height the machine has.

Return flanges and reverse bends. A return flange creates the same interference on a single side that a box creates on four: it folds back into the space a straight punch would otherwise use on a later bend. Switching to a gooseneck punch solves the flange interference but adds height to the upper tooling stack, which can turn into a new open-height shortfall if the stack isn’t rechecked.

Hems, offsets and multi-stage forms. A hem is usually an acute pre-bend followed by a flattening pass, and the part’s envelope changes shape between the two steps. Offset and Z-bends have the same issue in a different form: a feature formed in the first pass can block the backgauge or the tooling from reaching the correct position for the second. These need a bend-sequence review rather than a single final-shape check, since the interference usually doesn’t exist yet on the flat blank.

Long panels and wide flanges. A panel can fit well within the machine’s bending length and still be too long from front to back. As it bends, the trailing edge or an already-formed flange moves toward the C-frame, the backgauge structure or the sheet supports. Front support arms and sheet followers, when needed to keep a large panel stable, also occupy space during the bend and belong in the clearance check alongside the bare sheet dimensions.

Sizing a Machine From the Part Cross-Section

Mark every bend and find the critical one. Work from the finished part, not the flat blank. Note every bend line, angle, inside radius and flange height, plus the deepest formed section and any return flanges. The final bend in the sequence is usually the tightest fit, since it happens after the part already has its largest formed shape, though any step where a large panel rotates past a tool deserves the same scrutiny.

Record the real tooling stack. Catalog dimensions for a punch and die won’t tell you the installed height. Add the upper punch, punch holder or hydraulic clamp, any adapters, the lower die, the die holder or riser, and the planned V-die opening. Quick-change clamping systems and risers add setup flexibility but consume open height, and they need to be counted rather than treated as negligible hardware.

Check the vertical opening. Required open height needs to cover the upper tooling height, the lower tooling height, the maximum part envelope during the critical bend, and a safety margin for loading and removal. The maximum part envelope is the largest vertical space the workpiece occupies during that specific bend, a box wall, a formed flange, a rotating section, not the flat sheet thickness. The safety margin should cover normal tolerance stack-up in the material and tooling plus enough room to actually load and pull the part by hand or with a fixture.

Confirm the ram can reach the bend depth. Open height confirms the tooling and part fit into the machine; stroke confirms the ram can travel down to where the bend happens. For air bending, that depth depends on die opening, material thickness, tensile strength and target angle. Check it against the installed stack using CNC offline programming, bend simulation, or a trial bend in the actual material, rather than comparing rated stroke numbers between machines.

Check the rearward envelope against throat depth. On the critical cross-section, measure from the tooling centerline to the farthest point any part edge or formed flange reaches toward the rear of the machine. Compare that against usable throat depth, accounting for how the part rotates and where it needs support. For wide panels, also check clearance against the backgauge structure, sheet followers and any robotic or automated handling equipment along that same path.

Working Through a Deep U-Channel Example

Take a U-channel with two deep side walls and a return flange added on the last bend:

  • H = side-wall height
  • P = upper punch and holder height
  • D = lower die, holder and adapter height
  • C = handling and safety clearance
  • T = how far the formed part extends toward the rear frame

By the last bend, both side walls stand at height H, and a straight punch may interfere with the formed geometry. A gooseneck punch can provide the required relief, but its recessed profile must be checked against the actual flange envelope, bend sequence, and installed tool height. The punch and holder height become part of P, while the lower die, holder, and adapter height make up D.

A large enough open height doesn’t confirm the ram can reach the bend depth. That depends on the V-die opening and the material’s penetration requirement for the target angle, checked against the installed stack rather than the machine’s rated maximum stroke.

Finally, T gets compared against the usable throat depth. If the return flange pushes the part’s rear extension past that limit, it contacts the C-frame even on a machine with plenty of bed length and tonnage to spare.

Selection Mistakes Worth Avoiding

Sizing from a quote sheet that only lists tonnage and bed length. Many supplier quotes stop at these two numbers because they’re the easiest to compare across brands. Ask for open height, stroke and throat depth on the same sheet, with the reference points the manufacturer used to measure them.

Reading open height and stroke as one number. They measure different things, available space versus available travel, and a spec sheet lists them separately for a reason.

Using bare-machine dimensions instead of the installed stack. Holders, clamps, adapters and dies all consume the published opening. Run the numbers with the actual tooling, not the empty machine.

Checking the flat blank instead of the formed part. The largest envelope usually shows up two or three bends into the sequence, not on the original sheet.

Assuming a gooseneck punch solves every collision. It solves flange interference up to its own relief depth. Beyond that, the stack needs to get taller, which can eat into the open-height budget elsewhere, or the part needs a different bend sequence.

Mixing up throat depth and distance between uprights. One limits how far a part reaches behind the bend line; the other limits how long a deep-sided part can be before it has to rotate inside the frame instead of extending into the throat.

Press Brake Geometry Checklist

Before requesting a recommendation, have these details ready:

  1. Material grade and actual thickness
  2. Maximum bend length
  3. Bend angles, inside radii and tolerances
  4. Deepest formed dimension (box height, flange height, or similar)
  5. Return flanges, hems, offsets or reverse bends in the part
  6. Existing or preferred tooling dimensions
  7. Production volume and shift pattern
  8. Destination country, voltage and installation constraints

A cross-section sketch with these dimensions is enough to start a technical conversation.

Talk to CNHAWE Before You Order

CNHAWE’s engineering team reviews material, thickness, bend length, formed-part dimensions, tooling preferences and production volume against tonnage, bending length, open height, ram stroke and throat depth before recommending a configuration, so a clearance problem shows up in the review, not after the machine arrives.

Request a Press Brake Recommendation — share your material, thickness, bend length, part dimensions and production details through our inquiry form, and we’ll help define a configuration that fits your parts.

Ready To Upgrade Your Metal Fabrication Line? ​

Email Us For A Free Consultation Or Download Our Full Product Catalog.​

Related Recommendations

Scroll to Top

Official Notice

Only trust www.cnhawe.com and cnhawe.cn. The website cn-hawe.com is fraudulent.

Contact Us Now

If you would like to have a question then get in touch today, we are ready to assist 24/7. We welcome your cooperation and we will develop with you.