Professional Engineering Tool

Bend Allowance Calculator

Precision calculations for sheet metal fabrication. Compute bend allowance, bend deduction, K-factor, and flat pattern length with industry-standard formulas.

Precision Accuracy

Industry-standard formulas

Instant Results

Real-time calculations

Material Presets

Pre-configured K-factors

Input Parameters

Enter your bend specifications

mm
mm
°

Flat Pattern Calculation (Optional)

mm
mm

Bend Geometry

Bend Allowance (BA)
—
mm
Bend Deduction (BD)
—
mm
Outside Setback (OSSB)
—
mm
Neutral Axis Radius
—
mm
Flat Pattern Length
—
mm
Formula:
L1 + L2 - BD

Engineering Formulas

Industry-standard formulas used for precise bend calculations in sheet metal fabrication.

Bend Allowance Formula

BA = A × (π/180) × (R + K × T)

BA = Bend Allowance

A = Bend Angle (degrees)

R = Inside Bend Radius

K = K-Factor

T = Material Thickness

Description

Bend Allowance is the arc length of the neutral axis through the bend. It represents the amount of material that will be consumed by the bend. When a flat piece of metal is bent, the inside surface compresses while the outside surface stretches. The neutral axis is the theoretical line that remains the same length before and after bending.

Bend Deduction Formula

BD = 2 × OSSB - BA

BD = Bend Deduction

OSSB = Outside Setback

BA = Bend Allowance

Alternative: BD = 2(R + T) × tan(A/2) - BA

Description

Bend Deduction is the amount to subtract from the total of the flange lengths to obtain the flat pattern length. It accounts for the material that "grows" during bending due to the stretching of the outer surface. Use this value when you know the desired final dimensions and need to calculate the starting flat pattern size.

Outside Setback Formula

OSSB = (R + T) × tan(A/2)

OSSB = Outside Setback

R = Inside Bend Radius

T = Material Thickness

A = Bend Angle (degrees)

Description

Outside Setback (also called Outside Setback Distance) is the distance from the tangent point of the bend radius to the apex of the outside mold line. It's used to locate the bend line position relative to the outside corner of the bent part. This measurement is essential for accurate bend line placement.

Flat Pattern Length Formula

Flat Length = Leg1 + Leg2 - BD

Leg1 = First flange length (to bend line)

Leg2 = Second flange length (to bend line)

BD = Bend Deduction

Alternative: Flat = Leg1 + Leg2 + BA - 2×OSSB

Description

The Flat Pattern Length is the total length of the flat sheet metal blank before bending. By subtracting the Bend Deduction from the sum of the leg lengths, you get the exact size needed for the flat pattern to achieve your desired bent dimensions. This is crucial for cutting the correct blank size.

K-Factor Reference Guide

K-Factor values vary based on material type, thickness, and bending method. Use these guidelines as a starting point for your calculations.

By Material Type

Typical K-Factor values for air bending

Soft Aluminum (1100, 3003) 0.30 - 0.35
Hard Aluminum (5052, 6061) 0.35 - 0.40
Mild Steel (A36, 1018) 0.40 - 0.45
Stainless Steel (304, 316) 0.42 - 0.48
Copper (C110, C101) 0.32 - 0.38
Brass (C260, C360) 0.35 - 0.40
Titanium (Grade 2, 5) 0.42 - 0.48

By Bending Method

K-Factor varies with forming technique

Air Bending

Most common method. The punch doesn't force the material fully into the die.

K = 0.33 - 0.45

Bottoming

Material is pressed to the bottom of the die. More force required.

K = 0.40 - 0.45

Coining

High-pressure forming that compresses the material at the bend.

K = 0.45 - 0.50

Frequently Asked Questions

Common questions about bend allowance calculations

The K-Factor is a ratio that represents the location of the neutral axis relative to the material thickness. When metal is bent, the inside surface compresses while the outside stretches. The neutral axis is the theoretical plane where no compression or stretching occurs. K-Factor values typically range from 0.3 to 0.5, with 0.5 meaning the neutral axis is exactly in the middle of the material thickness. Accurate K-Factor selection is crucial for precise flat pattern calculations.

The most accurate method is to perform a test bend and measure the results. Start with the recommended values for your material type and bending method, then adjust based on actual results. Factors affecting K-Factor include: material hardness, grain direction, bend radius to thickness ratio, and bending method (air bending, bottoming, or coining). Many CAD software packages include material-specific K-Factor tables.

Bend Allowance (BA) is the arc length of the neutral axis through the bend—it tells you how much material is consumed by the bend itself. Bend Deduction (BD) is the amount to subtract from the sum of flange lengths to get the flat pattern length. Use BA when you're adding up segments to find total developed length. Use BD when you know the final dimensions and need to calculate the flat blank size.

Several factors can cause discrepancies: incorrect K-Factor for your specific material and setup, variations in material thickness, springback effects, die wear, and measurement errors. To improve accuracy: verify your K-Factor with test bends, use consistent measurement methods, account for material tolerances, and ensure your press brake is properly calibrated. Environmental factors like temperature can also affect results with some materials.

The inside bend radius significantly impacts all calculations. A smaller radius creates more material deformation and stress, while a larger radius distributes the strain more evenly. The minimum recommended bend radius is typically 1× the material thickness for soft materials and up to 3× for harder materials. Using a radius smaller than recommended can cause cracking on the outside surface. The radius also affects the K-Factor—tighter bends tend to shift the neutral axis closer to the inside surface.

Scroll to Top

Official Notice

Only trust www.cnhawe.com and cnhawe.cn. The website cn-hawe.com is fraudulent.